# Aero device engineering brief

Revision 0.3 · 12 November 2026

The Locket is intended for short requests to Aero. The first integration should let a user deliberately capture a request, review its transcript on the phone, then approve or discard the proposed change in Aero. The metallic CAD assemblies, mounting studies, print files, and a software link simulator are available now. The [Locket lab kit](https://rexzen.si/aero/download/#locket) adds development-board firmware and an Android receiver. The board and phone still need a paired bench run. Charging remains a separate milestone.

## Mechanical baseline

All sizes are nominal CAD dimensions in millimetres. The fit files are at https://rexzen.si/store/#hardware-files.

| Item | CAD specification | Evidence |
| --- | --- | --- |
| Locket enclosure | 32 × 44 × 10.4; 10.92 thick including slider; 4.0 strap opening | Ten-solid STEP assembly; separate rear and front STL shells |
| Cover | 0.20 seam and 0.20 tongue clearance per side; 1.6 rear wall below the pocket before rounding | Solid interference checked in CAD |
| Front details | Recessed Ø10.76 request key, separate mute slider and indicator. Two groups of three Ø0.76 acoustic bores, 16 apart centre to centre | Separate controls and port alignment geometry |
| Internal volumes | Board envelope 21.4 × 29.0 × 0.85, battery envelope 18.4 × 15.6 × 3.10, two 4.0 × 3.0 × 1.30 mic volumes | Space studies; complete electrical layout, sealing, and assembly pending |
| Clip and Loop | 11.5 × 30 shirt-clip tongue, 4.0 nominal free gap, 3.5 anchor bore aligned to the 4.0 shell eyelet, and a separate 14 outer diameter ring envelope | Clip gauge clears rear shell in CAD. Pin, load rating, retention, split-ring fit, and fabric tests are pending |
| Desk Dock | 74 × 62 × 13.8; recess 33.2 × 45.2, 4.9 deep; 0.60 clearance per side | One-piece dock STL and 14-solid seated STEP assembly; centered 25 mm approach and floor contact checked |
| Glasses | Approximately 145 wide; 54 × 33 lens envelopes | GLB form study with frame, temples, and optical housing |

Fit-print material and settings are trial parameters. Use a polymer fit sample before tooling. The proposed face is brushed or bead-blasted silver with a graphite polymer RF window and separate acoustic mesh. Keep the antenna clear of the metal face and body contact. Compare a painted polymer face with an aluminium cosmetic insert before committing to either process. A metal finish in a render does not certify RF performance. Remove the clip and ring before docking. The printed clip is a fit gauge. Do not use it to carry the Locket or keys until retention and fatigue are measured.

## First electronics bench

Use a USB-powered nRF52840 DK and an external PDM microphone as the reference setup if available. Zephyr's digital microphone sample documents that board as a tested target. The bench arrangement is external to the Locket so its geometry and wiring can be measured before a small board is designed.

- Capture target. One channel, 16 kHz, signed 16-bit PCM. Use a 15-second request limit for the first trial. That is up to 480,000 bytes of raw PCM, so the adapter needs bounded chunks and a documented overflow path. The limit is an input to the policy, not a measured device capability.
- Deliberate request. Begin with a dedicated bench button. On release, end the recording and offer the draft for review. The Locket CAD reserves a separate request control. Check button travel, assembly clearance, and actuation under clothing.
- Mute and indicator. The physical mute design should disable capture independent of firmware and expose a readable state. Measure the microphone path while muted, including reset and cable reconnect. The adapter must light the indicator before accepting samples. Loss of a trusted link, indicator readiness, or the capture limit discards the active buffer.
- Transfer and storage. Pair through an explicit phone flow and establish a trusted session before capture. The first integration should use a bounded temporary buffer and clear it when discarded. Confirm delivery and handle retries without saving duplicates. Persist only after the relevant user action and apply Aero's context settings.
- Dock. The current cradle has space reserved for contacts. Select and validate power input, charge control, cell protection, thermal behavior, connector wear, and mechanical retention on the bench before assigning charging or runtime specifications.

The original C policy can be downloaded from https://rexzen.si/assets/site/devices/aero-capture-policy.c. Compile its self-test with a C11 compiler.

```sh
cc -std=c11 -Wall -Wextra -Werror -DAERO_CAPTURE_SELFTEST aero-capture-policy.c -o aero-capture-test
./aero-capture-test
```

The policy starts in a wait-for-release state. Its host tests cover deliberate start, release to review, and every nonempty combination of the four fault inputs. The Zephyr adapter calls the same policy. The DK mute button gates capture in software. The LED command is observable on the board, but the bench has no independent light or microphone-power sensor.

## Locket to phone

1. Zephyr reads a mono PDM breakout on the USB-powered nRF52840 DK. Hold the request button to capture 16 kHz, signed 16-bit PCM. Release for review. The firmware stops capture at 14.5 seconds, inside the phone's 15-second limit.
2. Pair with the six-digit passkey displayed on the board's serial console. The secure GATT status read and subscription must succeed before capture. Each frame has a 12-byte little-endian header: version u8, kind u8, nonzero capture ID u32, sequence u16, payload bytes u16, reserved zero u16. Start uses sequence zero; later frames increment it. The receiver caps the payload at 228 bytes and a clip at 480 kB. Links below ATT MTU 185 are rejected. Audio needs 256 kbit/s before overhead. Measure sustained throughput and the usable range on the bench.
3. The Android receiver checks frame order and the active bond. It discards a clip on a gap, mute, link loss, malformed frame, or expiry. Capture needs the foreground lab; leaving that screen closes the connection. The simulator provides a synthetic stream separately.
4. The Android lab uses [Vosk](https://github.com/alphacep/vosk-api) for offline English transcription. After the one-time model install, try a short mono PCM WAV without a board. The app offers an editable transcript and only stages it when requested. Raw audio is never sent to a model provider by the lab. Text generation can use the separate desktop Aero Local kit or an available Aero provider.
5. Use Aero's existing context and action review after transcription. The model proposes a note, reminder, or answer. An action becomes real only when the user approves it. Show which sources and model are used. The Locket has no dedicated GNSS chip in this revision. One optional phone location reading can be rounded and added to a draft on the user's instruction.

## First component and fabrication sources

| Purpose | Candidate and source | Procurement or layout check |
| --- | --- | --- |
| USB electronics bench | [Nordic nRF52840 DK](https://docs.nordicsemi.com/r/bundle/ug_nrf52840_dk/page/ug/dk/intro.html), [Mouser India listing](https://www.mouser.in/en/ProductDetail/Nordic-Semiconductor/nRF52840-DK) | Check board revision and PDM pin access before wiring |
| Stereo PDM trial | Two [Infineon IM72D128](https://www.infineon.com/part/IM72D128), [DigiKey India cut tape](https://www.digikey.in/en/products/detail/infineon-technologies/IM72D128V01XTMA1/16730911) | Separate gaskets and 16 mm port spacing. Recheck package, clock mode, footprints, acoustic seals and assembly yield |
| Rechargeable revision | [TI BQ25180](https://www.ti.com/product/BQ25180), [DigiKey India](https://www.digikey.in/en/products/detail/texas-instruments/BQ25180YBGR/15857374) | Select a protected cell and thermistor first. Confirm ratings, power path, enclosure heat and qualified assembly before connecting a battery |
| PCB and assembly | [PCB Power](https://www.pcbpower.com/page/about-us) | Ask for assembly capability with bottom-port microphones and small packages after schematic and PCB review |
| Mechanical fit samples | Local FDM or SLS print service for shell and gauge. [think3D](https://www.think3d.in/) for a quote on machined and printed samples | Quote polymer and machined face separately. Use the STEP and tolerance notes. Request material, finish, measured dimensions, minimum quantities, and lead times |

These are sourcing candidates, not supplier commitments. The first spin uses a catalog radio and microphone. A custom chip would add packaging, firmware, qualification, and production risk before the signal path is proven.

## Release gates

| Gate | Pass condition |
| --- | --- |
| Fit sample | Print all three parts at nominal scale. Record measured widths, lengths, and depth. Fit the front cover, seat the Locket against the floor, and lift it with the scoop. Repeat 25 cycles and inspect for binding, cracks, and drift. |
| Audio and privacy bench | Verify the visible indicator before the first frame. Test held input at boot, mute while recording, lost link, indicator failure, and capture limit. Each fault must stop and discard capture. Recovery must require a new press. For range, record the same phrases at 0.25, 0.5, 1, 2 and 4 m with clothing rub, background speech, and quiet controls. Compare word error rate, trigger success, dropouts, and time to draft for each mount and distance. Publish a range only after measuring it. |
| Phone and Aero | Test pairing, disconnect, duplicate delivery, and deletion using a fixed script. A test request to set a reminder must produce a reviewable draft. Confirming creates it once; discarding leaves the workspace unchanged. |
| Wear and power | Measure weight, battery runtime, temperature, retention, and behavior in wear. Select materials and a retention method against those results. Evaluate charging and enclosure tests before publishing a claim. |
| Store release | Approve a physical sample and finalize sizes or dimensions, product identifiers, inventory, price and currency, fulfillment, returns, and payments before opening orders. Until then the Store carries software, CAD downloads, and labeled merch previews. |

## Reference repositories

- [Zephyr DMIC sample](https://github.com/zephyrproject-rtos/zephyr/tree/v4.2.0/samples/drivers/audio/dmic) and [supported bench targets](https://docs.zephyrproject.org/latest/samples/drivers/audio/dmic/README.html) inform the bench selection.
- [Omi firmware](https://github.com/BasedHardware/omi/blob/main/omi/firmware/readme.md) is a reference for real wearable audio, streaming, and firmware organization. Aero's capture policy is original host code.
- [Vosk](https://github.com/alphacep/vosk-api) provides the native Android recognizer and offline English model. [llama.cpp](https://github.com/ggml-org/llama.cpp) runs the desktop model in Aero Local.
- [Rexzen source](https://github.com/9aman-og/rexzen) contains the site and checksum-pinned application archive. The archive includes the original build123d generator and the Three.js viewer.
