# Aero Locket Screen · fit and integration brief

One pocket-sized core has a touch display, crown, independent microphone mute, an indicator on the permanent frame, and four interchangeable accessories. The upper case is a brushed-metal collar and hinged lid. Two service screws release the entire metal assembly; the display and enclosure stay assembled. Keep the lid for the pendant or keyring, or remove it for an unobstructed watch display. The mount fits the same mechanical interface in all four modes.

## Assembly and fit

- The 37 × 48 mm core uses a rounded polymer rear shell, a deep graphite display frame, and a cobalt mute control. The closed projection including the crown is approximately 40 mm wide. See `fit-check.json` for the exact closed envelope. The cover opens through 108°. The hinge pin is an envelope in the fit model. A durable hinge needs an axial retainer, a positive close detent, and a stop validated for impact and finger clearance.
- The 1.69-inch, 240 × 280 reference module has a 33.13 × 41.13 mm touch-panel outline and an active area of about 27.97 × 32.63 mm. The model includes glass, LCD and rear optical envelopes. Confirm the actual cable path, adhesive lands, bezel tolerances, and glass stack against a vendor sample before routing the PCB. [Waveshare touch module and drawing](https://www.waveshare.com/wiki/1.69inch_Touch_LCD_Module)
- For the upper case, start with satin 6061 aluminium and a stainless hinge pin. The lid protects the glass in pendant and keyring use. The fixed polymer housing and glass form the proposed environmental seal. The lid does not provide that seal. Keep the BLE and GNSS antenna regions clear of metal, battery and skin. Test with the lid open, closed, and removed, worn and held, and in a pocket.
- Each accessory has two keyed rails with 0.22 mm nominal clearance per side. Slide toward the end stop and retain with the cross-axis pin before applying load. The watch saddle makes a 22 mm strap interface and exposes the back optical window. Pendant and keyring saddles use separate loops. The shirt clip is a fit gauge for a qualified spring part. Test rail insertion tolerances, pin capture, strap pull, clip reversal, repeated wear and drop. The spring bars, rings and straps in the STEP are simplified envelopes.
- Eight STL parts and one engraved identification coupon can be used for fit checks. Print only the empty shells, collar, lid and saddles. Leave the electronics out. Follow the raw printable file geometry when planning support. The first build should use inert hardware and no battery. Seal stack-up, screws, spring force, abrasion, sweat, charging and ingress are bench measurements; the CAD has no water resistance rating.
- The existing nRF52840 DK firmware and original Desk Dock remain available as separate bench artifacts. This screened core uses a different rail, contact spacing and body size. A revised charging cradle, reverse-polarity isolation, pogo contacts and PMIC firmware require their own electrical and physical test.

## First electronics prototype

| Function | Bench candidate | Integration |
| --- | --- | --- |
| Control and radio | [Nordic nRF5340](https://docs.nordicsemi.com/r/bundle/ps_nrf5340/page/keyfeatures_html5.html) | Zephyr BLE and a bounded accessory service. SPI draws dirty rectangles on the screen, I²C reads touch and sensors, PDM handles the matched microphones, and I²S drives a small speaker through an external amplifier. A full 240 × 280 RGB565 frame is about 131 KiB. Start with line or tile buffers and profile RAM while recording. |
| Touch and display | [Waveshare 1.69-inch module](https://www.waveshare.com/wiki/1.69inch_Touch_LCD_Module) | ST7789V2 display and CST816S touch for a dev board. Screen sleeps when lid is shut. Use the crown or a persistent keyboard control to wake and exit.
| Voice | Two [Infineon IM73D122](https://www.infineon.com/part/IM73D122) PDM candidates | Two isolated acoustic paths 18 mm apart on the fixed frame. A physical switch should cut the mic rail. Tie the recording light to microphone power through an independent current-sensed path and fail closed. Measure voice intelligibility in wind, street noise, fabric cover and rooms from 0.3 to 3 m. Report word error rate and distance together. |
| Motion and activity | [Bosch BMI270](https://www.bosch-sensortec.com/en/products/motion-sensors/imus/bmi270) | Use wrist mode for motion-based steps, lift to wake, optional sleep research, and quiet hours. Characterize the algorithm across walking speeds and mounting styles. No automatic sleep-stage or mood inference from this sensor. |
| Wellness exploration | [Analog Devices MAX86141](https://www.analog.com/en/products/MAX86141.html) | The wrist-facing window reserves space for a reflective optical sensor. Only sample in wrist mode with explicit opt-in. Validate fit, stray light, motion and skin-contact detection. The fit pack represents the optical window, and no health measurement has been demonstrated. |
| Power and haptics | [Nordic nPM1300](https://docs.nordicsemi.com/r/bundle/ps_npm1300/page/keyfeatures_html5.html) plus protected cell and LRA driver | Profile sleep, video-free screen-on, voice capture, ring, haptic, Bluetooth reconnect and GNSS. Put the temperature sensor against the cell, monitor charge temperature, and carry out fault testing before enabling contact charging. Retain a local timer with the phone disconnected. No runtime is quoted. |
| Optional standalone position | [u-blox MAX-M10S](https://content.u-blox.com/sites/default/files/MAX-M10S_DataSheet_UBX-20035208.pdf) | Separate RF daughterboard experiment after battery and antenna validation. GNSS estimates a position only while powered and in suitable coverage. It needs a phone or separate service to relay a remote position. The CAD package does not include a signed-off GNSS antenna, UWB, or cellular transmitter. |

The labels in this table are evaluation candidates. Prefer the display and a phone-connected board first, using the existing BLE capture bench. Then fit inert component models, get tolerances from the enclosure and display vendors, and prototype the actual electronics in a larger body before shrinking to the CAD outline. No components were ordered.

## Watch and accessory software

The on-site preview is an engineering interaction model with fictional events and measurements. The device concepts include a clock, timers, notification snippets, meeting reminders, action review, activity, an independent mute, haptics, nearby ring and last seen. The current Android app provides the voice draft workflow, local speech, chats and alarms. The screened device has no production firmware or verified board.

- **Link.** One accessory per owner bond over encrypted LE Secure Connections. Rotate BLE addresses, store bond material with the platform keystore, and clear it on a local ownership reset. Discover and subscribe to one expected service. Drop partial audio on a bad frame, sequence gap, lost indicator or link loss. Transfer complete short clips only when the hardware request is held. Associate each completed clip with one expiring draft; never submit it again after reconnect.
- **Voice.** The phone is the normal transcription and inference host. Use the paired Android app for offline transcription; any external model gets only the reviewed request and selected context. Offer an explicit cloud choice. A wake cue, battery, mute and receive status remain legible with the lid shut by using hardware haptic and indicator signals. Read a reply aloud over the phone or a future speaker path after review. Images remain a phone input.
- **Watch.** The clock, local timers and cached due reminders should work away from the phone. Time sync carries UTC, monotonic capture time and zone. Display whether a cached reminder has synced. Open a meeting reminder on the phone after the user taps. The alarm gates dismissal on the configured interaction; the current Android three-answer alarm is the reference. Calendar edits, messages, and payments keep the phone’s existing confirmation and authorization path.
- **Keyring.** Start with owner-only, authenticated nearby ring and a timestamped phone-observed last-seen point. Do not publish an identifiable tag ID or share a live location by default. Missing or stale data explains itself. Broader finding requires a compatible accessory network and a dedicated approval, qualification, and unwanted-tracking implementation. Include an audible alert, physical identification, local disable instructions, rotating identifiers, and detection tests before any remote finding pilot. Use the [Google Find Hub accessory specification](https://developers.google.com/nearby/fast-pair/specifications/extensions/fmdn) for scope. The preview uses neither Bluetooth nor location permissions.

## Release evidence

`fit-check.json` records the kernel-level solid checks, lid sweep, collar lift, fitted accessories and rail insertion at sampled positions. The build reimports each STEP assembly to check solid count and validity. Fit geometry excludes the actual harness, waterproofing, RF, production tooling and surface finishing. The browser preview demonstrates the interaction and CAD articulation. An assembled device, acoustics, GPS, tracking, health measurements, and battery performance require physical validation.

For sample sourcing, use Waveshare for the screen, Nordic distributors for development boards, and Infineon evaluation boards for the microphone comparison. The original bench brief lists existing enclosure and print-service candidates. Give a fabricator the R01 drawing and STEP together and get the tolerance, actual material and finish in their response before approving an order.
